I have a solution for you but the Taylor Made Solar Powered LED Dock Light - Aluminum - 4-1/8" Long x 4-1/8" Wide item # TM47VR can not be turned on and off. For a solar powered LED Dock light than can be turned off you are going to want the Taylor Made Solar Powered Overhead Light w/ Motion Sensor - 6-5/8" Long x 4-3/8" Wide item # TM94VR. view full answer...
The most common mounting location of the LED Pontoon and Fishing Boat Docking Lights part # TN23ZR on a pontoon boat is on top of the deck at the outside corners facing out. That said, we do have a better option more specific to pontoon boat trailers, the LED Docking Light for Pontoon Boats part # TN98XR or part # TN48XR which would mount to the side of the deck floor at the front or side facing out. view full answer...
To change the bulb on the Optronics Halogen Docking Light, part # DL-16CC, you just remove the 2 screws that are on the front of the light, one on each side of the lens. You then need to pull the assembly out of the housing and on the back there is a small screw that needs to be removed as well. When that is removed the entire light assembly will be able to be replaced.
The # DL-16CC kit uses two 35-watt halogen lights. view full answer...
On a boat you would want to ground docking lights # DL-16CC to the negative battery terminal.
The pin on the top of the switch runs to the ground, the middle supplies power for the lights, and the bottom pin runs to the positive post of a battery through a fuse. view full answer...
I can certainly provide you some installation instructions for the Halogen Docking Light Kit, # DL-16CC.
First, drill a hole at the desired mounting locations, slip on the rubber boot cover, then install the lights using the included hardware. Disconnect the battery to avoid short circuits/electrical shock. Measure the wire needed to install the lights on your boat and cut the red wire into the lengths needed. Place the plastic terminal covers onto the wire and attach the corresponding... view full answer...
On a boat you would want to ground docking lights # DL-16CC to the negative battery terminal. You will want the connections to be water tight as best as you can. Shrink tubing, electrical tape, and even liquid electrical tape # SWC50122 will help protect electrical connections from water. You can also use dielectric grease, # 11755, between electrical connections. This special grease is hydrophobic so it will repel moisture. view full answer...
The switch has 3 terminals, ground, power in, power out. The power out terminal will be split to the 2 different lights in kit # DL-16CC. The pin on the top of the switch runs to the ground, the middle pin supplies power for the lights, and the bottom pin is for the power supply wire and goes to the fuse box or the positive post of a battery. (See image.) view full answer...
Since the switch only has the 3 terminals, ground, power in, power out, only the power out would be split to the 2 different lights in kit # DL-16CC. There only needs to be one ground (negative) at the negative battery terminal and there is just the one 12 volt power source coming from the positive battery terminal. view full answer...
Although I don't have an install video available to direct you to, I can explain the installation for you.
As you stated, the red wire is connected to a power source. The black wire is for the ground connection, preferably the negative battery terminal. view full answer...
Since the switch is lighting up, but the lights aren't coming on, it sounds like you have your power wires correct, but the problem is with the ground wire on your Halogen Docking Lights # DL-16CC. The black wire from the lights is the ground wire for the lights. There are a few ways you can go about grounding your lights.
You could run a wire from each light's ground wire to the negative post on your battery, or ground it to the steel frame. You can use a ring terminal, like # DW05705-1,... view full answer...
I reached out to Jif Marine and if you use a marine grade adhesive on the # JIF56VR it will likely hold up when paired with the screws on the top. However, this has not been tested so there are no guarantees. view full answer...
Yes, the:
-TeraPump Fuel Transfer Pump for Gas Cans and Racing Utility Jugs # TE87VR will work fine with 110+ octane racing gas.
This pump is perfect for race tracks, garages, shops, yards, farms, docks, and campsites, and will also work with non-corrosive liquids, such as gas, non-potable water, kerosene, diesel, or light oils.
Additionally this pump runs off of 4 AA batteries, so if you need some you can use # DU58QR. view full answer...
You do have a few options to get an electric winch, like the Dutton-Lainson StrongArm # TW4015, working, but the 4 Flat will not be able to do so alone.
The first will be to add a battery to the trailer. This will usually be my suggestion, but as you do not have brakes on the trailer and it is for a boat trailer, it will not be the best way to go.
What I suggest doing is upping your 4 Flat to a 5 Round, both on the trailer and vehicle. The Pollak 5-Pole # PK11502 for the vehicle side,... view full answer...
Go To Results